The much-anticipated MG kit of Destiny Gundam is here, and is definitely not one to disappoint!
The joints on this sharply detailed MG kit are greatly improved to allow for a wider range of movement and are more capable of replicating action poses as seen in the show. The wings can open and close, and it comes complete with its signature weaponry along with in-scale unpainted figures of Shinn Asuka (sitting and standing) and Stella Loussier.
Foil stickers and original design marking stickers are included for custom markings, plus a custom display stand to assist with dynamic action poses.
The third kit in the Real Grade line is the GAT-X105 Aile Strike Gundam. Bandai gives the Strike some REAL attention!
It comes with a shield, beam rifle, two beam sabers, plenty of marking stickers, and an adaptor so it can fit on an Action Base 1, and most importantly off all, that amazingly engineered Advanced MS Joint frame!
To coincide with the 10th anniversary of Gundam Seed Bandai has rereleased this hugely popular HG kit of the Buster Gundam in a 'remastered' color reflecting those seen on the upcoming Blu-ray release.
A stand attachment and marking stickers are also included in this special release.
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you!
High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰)
Steps for Applying Decals to Gunpla:
1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want.
2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet.
3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla.
4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish.
5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment.
Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
Marking the 20th anniversary of the Master Grade Ver.Ka series is the incredible MG Zeta Gundam Ver.Ka from "Mobile Suit Zeta Gundam"!
The proportions of the Gunpla are based on Kazumi Fujita's sketches of the Gundam for the anime. The structure and shape have been refined to ensure that there is no breakdown in the form between both the MS form and the Waverider form, and the transformation mechanism has been expertly constructed.The MS form has a wide range of motion, allowing for a greater degree of recreation of poses from the show. The Waverider form can be displayed in a stable manner like a fixed aircraft model by providing a locking mechanism for each part.The MG Zeta Gundam also features parts with metallic extra finish processing, along with water transfer decals designed by Katoki Hajime.
From "Mobile Suit Gundam SEED" comes a completely new GAT-X131 Calamity Gundam, the first in a new series of "FULL MECHANICS" action figure kit!
The head pulls out from the body and has a built-in gimmick to ease the buffer using the collar parts. The movable axis of the abdomen can swing both back and forth, and left to right.The Todesu Block is included as a handheld weapon. The grip can be swung forward for a powerful stance! The Kafer Zwei (shield) is included with a swinging barrel, as well!
Order this incredible action figure for your collection today!
Piloted by Sven Cal Bayan as seen in the "Gundam Seed Stargazer" Original Net Animation series, the fan-favorite Strike Noir Gundam mobile suit finally gets the Master Grade treatment!
Strike Noir Gundam comes with highly detailed mechanisms, a super-articulated inner frame that allows its signature action poses to be recreated, and plenty of weaponry including the Noir Striker unit, three beam rifles, two "Fragarach 3" beam blades, two anchor cables and more, plus four pairs of optional hands. Decals are included for custom markings.
Get one for yourself now!
To coincide with the 10th anniversary of Gundam Seed Bandai has rereleased this hugely popular HG kit of the Duel Gundam Assault Shroud in a 'remastered' color reflecting those seen on the upcoming Blu-ray release.
A stand attachment and marking stickers are also included in this special release.
Fantastic high-grade injection plastic kit of the Sword Impulse Gundam will be great fun to build up.
Parts molded all in colour mean you don't need to paint it; and all the parts snap neatly together, so no glue is required, either. Stickers for detail are included; and polycaps at the joints mean the finished model will be poseable.
The completed model can also transform, separating the Core Splendor, Leg Flyer, and other parts.
Check out the guns on this guy! And the amazing amount of missile pods! Heavy Arms lives up to its name by sporting missile pods on its shoulders, skirt, and legs and if that wasn't enough he also carries around that massive gun!
Molded completely in color the Heavy Arms snaps together easily and once finished will stand in a variety of poses.
It also comes with an option assembly for the arm allowing it to store a beam saber handle and a whole lot of markings (sticker and dry transfer).
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you!
High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰)
Steps for Applying Decals to Gunpla:
1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want.
2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet.
3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla.
4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish.
5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment.
Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you!
High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰)
Steps for Applying Decals to Gunpla:
1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want.
2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet.
3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla.
4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish.
5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment.
Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you!
High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰)
Steps for Applying Decals to Gunpla:
1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want.
2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet.
3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla.
4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish.
5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment.
Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you!
High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰)
Steps for Applying Decals to Gunpla:
1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want.
2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet.
3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla.
4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish.
5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment.
Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you!
High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰)
Steps for Applying Decals to Gunpla:
1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want.
2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet.
3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla.
4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish.
5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment.
Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you!
High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰)
Steps for Applying Decals to Gunpla:
1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want.
2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet.
3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla.
4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish.
5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment.
Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you!
High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰)
Steps for Applying Decals to Gunpla:
1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want.
2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet.
3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla.
4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish.
5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment.
Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you!
High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰)
Steps for Applying Decals to Gunpla:
1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want.
2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet.
3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla.
4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish.
5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment.
Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
Bandai's Real Grade Justice Gundam keeps the excellence of the series going with an amazingly detailed kit complete with opening hatches, effect parts, and so many markings.
Justice Gundam can also be mounted onto his backpack securely thanks to Bandai's great design for the feet.
Marking Bandai's 100th entry in the High Grade Universal Century plastic kit series, here's an incredibly detailed snap-fit kit of the titular mecha from "Mobile Suit Gundam UC" in Destroy Mode!
This milestone kit comes molded in color and features newly introduced polycap joints that allow for a wider range of posing possibilities! Its psycoframe is molded in clear pink plastic, and it comes armed with two beam sabers, a beam magnum, and a shield. Foil stickers are provided for detail.
Here comes the fourth model kit from Infinite Dimension, Thunderbolt 雷霆 from the RDM series! A highly detailed model kit made with high quality materials.
This is a kit that all mecha lovers will not want to miss!
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you!
High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰)
Steps for Applying Decals to Gunpla:
1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want.
2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet.
3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla.
4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish.
5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment.
Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
Here comes this latest amazing model kit by Iron Toys, the Star Eternal!
Coming in dual color scheme of your preference, this highly detailed model kit is made with quality materials. Star Eternal is definitely a kit that all mecha lovers will not want to miss!
Get one for your collection today!
A variant of the Gundam Astray Red Frame featured in the side story "Gundam Seed VS Astray" appears in MG form!
Its characteristic red and white inverted colors along with giant V-Fin, chin guard, and original backpack have been faithfully recreated! Gundam Astray Turn Red features 2 Tactical Arms packs that can convert between massive buster sword and stationary chain gun.
A small display base is provided to help balance the weight of the Tactical Arms. Hip mounted Armor Schneiders beam rifle, and shield round off its arsenal. Beam rifle and shield parts can be retrofitted on the MG Astray Red Frame to show its original form!
Get one for yourself now!
