Model Kit Accessories
FLAMING SNOW MG-41 | 1/100 NU GUNDAM VER. KA FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW MG-11 | 1/100 PROVIDENCE GUNDAM FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW MG-82 | 1/100 STRIKE ROUGE GUNDAM FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$7.90$6.90
FLAMING SNOW RG-01 | 1/144 RX-78-2 GUNDAM FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW RG-45 | 1/144 GOD GUNDAM FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
KOSMOS LED UNIT FOR HG GUNDAM CALIBARN/AERIAL REBUILD (TYPE B)
Beautify your display setup with this effect accessory set, specially crafted for High Grade Gundam Calibarn and Gundam Aerial Rebuild by KOSMOS! Suitable for: High Grade Gundam Calibarn (LED Gund-Bits Permet Belt) - HG Type B High Grade Gundam Aerial Rebuild (LED Gund-Bits Permet Belt) - HG Type B Features: Customizable LED for Gund-Bits Permet Belt Adjustable lighting colors effects (Require KOSMOS app) Perfect & easy fit Model kit and display stands are not included.
$29.90$25.90
BANDAI 1/100 GUNDAM MS CAGE/DOCK/HANGAR (METAL GREY)
The Gundam MS Cage/Dock designed by BW is a replica of the integrated facility "Gundam Base", and can hold Gundam model kits of the 1/100 scale models. Comes with a set of waterslide decals to give the MS cage additional detailing! Easy to assemble and great for displaying your model kits, replicating the Gundams' docked scenes from their anime! Don't miss this, get one for yourself now!
$19.90$16.90
FLAMING SNOW RG-51 | 1/144 EPYON FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
DDB CORGI THE WITCH FROM MERCURY DISPLAY STAND (BLACK) FOR FM GUNDAM AERIAL
Beautify your display setup with this effect accessory set, specially crafted for Gundam Aerial! Can be combined with the Gundam Aerial Permet Effect Unit + Gund-bits Weapon Display Base to showcase Gundam Aerial at its finest! Suitable for: Full Mechanics Gundam Aerial Model kit and Effect Unit + Weapon Display Base is not included.
$11.90$9.90
KOSMOS LED UNIT FOR HG GUNDAM AERIAL (TYPE A)
Beautify your display setup with this effect accessory set, specially crafted for High Grade Gundam Aerial by KOSMOS! Features: Customizable LED for Gund-Bits Permet Belt Adjustable lighting colors effects (Require KOSMOS app) Perfect & easy fit Model kit and display stands are not included.
$29.90$25.90
FLAMING SNOW PG UNLEASHED 1/60 RX-78-2 GUNDAM FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW HG-63 | 1/144 GUNDAM LFRITH FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW MG-53 | 1/100 FORCE IMPULSE GUNDAM FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$7.90$6.90
FLAMING SNOW MG-54 | 1/100 SWORD IMPULSE GUNDAM FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$7.90$6.90
FLAMING SNOW MG-90 | 1/100 AEGIS FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW MG-81 | 1/100 BUSTER GUNDAM FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW MG-60 | 1/100 INFINITE JUSTICE GUNDAM FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$7.90$6.90
FLAMING SNOW RG-04 | 1/144 FREEDOM GUNDAM FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW RG-21 | 1/144 FREEDOM GUNDAM VER. GCP FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW RG-32 | 1/144 NU GUNDAM FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
KOSMOS LED UNIT FOR PG UNICORN GUNDAM
Beautify your display setup with this effect accessory set, specially crafted for Perfect Grade Unicorn Gundam by KOSMOS! Features: Customizable LED Unit for Main Body & DE Shield Adjustable lighting colors effects (Require KOSMOS app) Perfect & easy fit Supports USB power source or battery (does not come with battery) Model kit and display stands are not included.
$90.90$77.90
FLAMING SNOW PG-01 | 1/60 GUNDAM EXIA FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$10.90$8.90
FLAMING SNOW MG-138 | 1/100 ZETA GUNDAM VER. KA FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW EG-04 | 1/144 NU GUNDAM FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90