Model Kit Accessories
FLAMING SNOW RG-37 | 1/144 SWORD IMPULSE GUNDAM FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW MG-17 | 1/100 RX-78-2 GUNDAM VER. 3.0 FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW MG-43 | 1/100 UNICORN GUNDAM 03 PHENEX (NARRATIVE VER.) FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$7.90$6.90
FLAMING SNOW RG-08 | 1/144 00 GUNDAM SEVEN SWORD FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW RG-20 | 1/144 00 QAN[T] FULL SABER FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW RG-18 | 1/144 00 RAISER (ORIGINAL/TRANS-AM) FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW RG-27 | 1/144 UNICORN GUNDAM 02 BANSHEE NORN FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW RG-19 | 1/144 WING GUNDAM EW FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW HG-70 | 1/144 PSYCHO ZAKU FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW HG-41 | 1/144 NIGHTINGALE FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$7.90$6.90
FLAMING SNOW MG-FA78 | 1/100 FULL ARMOR GUNDAM FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$8.90$7.90
FLAMING SNOW MG-26 | 1/100 FULL ARMOR UNICORN GUNDAM VER. KA FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$10.90$8.90
FLAMING SNOW MG-50 | 1/100 GUNNER ZAKU WARRIOR (LUNAMARIA HAWKE) FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$8.90$6.90
FLAMING SNOW MGEX-63 | 1/100 UNICORN GUNDAM VER.KA FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$8.90$7.90
FLAMING SNOW RG-31 | 1/144 CROSSBONE GUNDAM X1 FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW RG-24 | 1/144 GUNDAM ASTRAY GOLD FRAME AMATSU MINA FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW RG-05 | 1/144 MK-II A.E.U.G./TITANS FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW RG-22 | 1/144 SINANJU FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW MG-86 | 1/100 GUNDAM BARBATOS (XUAN WU VER.) FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW RG-49 | 1/144 DESTINY IMPULSE GUNDAM FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW HGCE-90 | 1/144 FORCE IMPULSE GUNDAM SPEC II FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW HG-45 | 1/144 WING GUNDAM ZERO FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW MG-31 | 1/100 00 GUNDAM SEVEN SWORD FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW MG-74 | 1/100 EPYON FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90