Model Kit Accessories
FLAMING SNOW HG-91 | 1/144 MIGHTY STRIKE FREEDOM GUNDAM FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW HG-61 | 1/144 BEGUIR-BEU FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW HGCE-90 | 1/144 FORCE IMPULSE GUNDAM SPEC II FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW HG-64 | 1/144 DEMI TRAINER+MIRASOUL FLIGHT UNIT FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW HG-90 | 1/144 DESTINY GUNDAM SPEC II FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW HG-66 | 1/144 DILANZA (GUEL CUSTOM/STANDARD) FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW HG-57 | 1/144 GM (SLEGGAR) FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW HG-55 | 1/144 GM SNIPER II FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW HG-20 | 1/144 GUSTAV KARL FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW HG-62 | 1/144 MICHAELIS FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW HG-54 | 1/144 RX-78F00 GUNDAM FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW HG-52 | 1/144 GOUF FLIGHT TYPE FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW MG-21 | 1/100 00 XN RAISER FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW MG-44 | 1/100 GUNDAM AGE II MAGNUM FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW MG-157 | 1/100 CHAR'S Z'GOK FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW MG-132 | 1/100 DEATHSCYTHE EW FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW MG-62 | 1/100 DEATHSCYTHE HELL EW FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW MG-109 | 1/100 GUNDAM EX IMPULSE FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW MG-24 | 1/100 GUNDAM F91 VER 2.0 FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW MG-07 | 1/100 FENICE RINASCITA FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW MG-149 | 1/100 JOHNNY RIDDEN'S GELGOOG FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW MG-29 | 1/100 RX-75 GUNTANK FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW MG-129 | 1/100 GUNDAM HEAVYARMS FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW MG-57 | 1/100 GUNDAM KYRIOS FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90