Products
FLAMING SNOW MG-18 | 1/100 RX-78-2 GUNDAM VER. KA FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW MG-19 | 1/100 ZZ GUNDAM VER.KA FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$7.90$6.90
FLAMING SNOW MG-21 | 1/100 00 XN RAISER FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW MG-23 | 1/100 UNICORN GUNDAM 02 BANSHEE VER. KA FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$7.90$6.90
FLAMING SNOW MG-24 | 1/100 GUNDAM F91 VER 2.0 FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW MG-25 | 1/100 AILE STRIKE GUNDAM (METAL BUILD DESIGN) FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW MG-26 | 1/100 FULL ARMOR UNICORN GUNDAM VER. KA FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$10.90$8.90
FLAMING SNOW MG-27 | 1/100 GUNDAM EXIA FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW MG-28 | 1/100 GUNDAM DYNAMES FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW MG-29 | 1/100 RX-75 GUNTANK FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW MG-30 | 1/100 REZEL FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW MG-31 | 1/100 00 GUNDAM SEVEN SWORD FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW MG-32 | 1/100 ZAKU II (UNIVERSAL) FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW MG-40 | 1/100 SINANJU STEIN (NT VER.) VER. KA FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW MG-41 | 1/100 NU GUNDAM VER. KA FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW MG-42 | 1/100 SAZABI VER. KA FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$7.90$6.90
FLAMING SNOW MG-43 | 1/100 UNICORN GUNDAM 03 PHENEX (NARRATIVE VER.) FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$7.90$6.90
FLAMING SNOW MG-44 | 1/100 GUNDAM AGE II MAGNUM FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW MG-47 | 1/100 SINANJU FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$7.90$6.90
FLAMING SNOW MG-50 | 1/100 GUNNER ZAKU WARRIOR (LUNAMARIA HAWKE) FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$8.90$6.90
FLAMING SNOW MG-51 | 1/100 GUNDAM BARBATOS FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$6.90$5.90
FLAMING SNOW MG-53 | 1/100 FORCE IMPULSE GUNDAM FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$7.90$6.90
FLAMING SNOW MG-54 | 1/100 SWORD IMPULSE GUNDAM FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$7.90$6.90
FLAMING SNOW MG-55 | 1/100 BLAST IMPULSE GUNDAM FLUORESCENT WATERSLIDE DECAL
Note: If there is a certain waterslide decal you are looking for, but is not available on our site, you can PM us to check with us so we can source it for you! High quality and detailed waterslide decal by Snow Flame/Flaming Snow Studios (雪焰) Steps for Applying Decals to Gunpla: 1. Cut out the desired design or icon from the decal sheet and trim it to achieve the exact size you want. 2. Dip the cut decal into water for approximately 30 seconds. This allows the decal to detach easily from the decal sheet. 3. Using a pair of tweezers and a cotton swab, gently slide the decal from the backing sheet to the precise location on your Gunpla. 4. After placing the decal, adjust or realign it to your satisfaction. With a dry cotton swab, gently roll over the decal to absorb excess water.Smooth the edges and remove any bubbles for a flawless finish. 5. Leave the applied decal to dry completely.Remember: If the decal back sticks together, use the toothpick method in water for safe detachment. Important Note: Do not attempt to detach the decal directly in the water, as its adhesive is extremely strong. In case the back of the decal sticks together, place the decal in water and use a toothpick to carefully detach it.
$7.90$6.90